| |
Subject |
Author |
Date Posted |
Forum
|
 |
RE: Tail lights not working on Bounder
hi mikey,
welcome to the forum. i think i would start with the wiring.....now if your tow dolly is not hooked up, do the lights work then? that way you will know where to go, the dolly or the motor home.
steve
|
stevesandidge
|
12/11/09 08:42pm |
Tech Issues
|
|
RE: Fleetwood Bounder Transfer Switch
yes he needs to see what the voltage is AT the transfer switch. remember it has to see the voltage to switch from shore to genset. BUT it does not have to "switch" with shore power as it is the default in the transfer sw.
steve
|
stevesandidge
|
12/08/09 06:28am |
Tech Issues
|
|
RE: Looking for quick help on Atwood furnace
the limit sw, or more correctly the HIGH limit sw, is located at the back of the furnace and is held in place with 2 screws. once they start cutting off, therafter they cut off easier n easier. i agree with the corrosion comment, have fixed many many of em just by cleaning contacts. hope ya stay warm!
steve
|
stevesandidge
|
12/05/09 03:02pm |
Tech Issues
|
|
RE: Tripping GFI breaker
kottfam speaks true. you unwired it and it works, sounds like ya went to irv2 and them knowitalls showed thier azzes! lol don't take it personally, some of those folks over there are just impressed with themselves! lol
steve
|
stevesandidge
|
12/05/09 02:54pm |
Tech Issues
|
|
RE: jacks what brand
could be HWH as well. try thier website too.
steve
|
stevesandidge
|
11/15/09 05:37pm |
Tech Issues
|
|
RE: Problem with propane detector??
i agree with java on this, better safe than dead.
stece
|
stevesandidge
|
11/15/09 05:20pm |
Tech Issues
|
|
RE: Skylight source and material recommendations
try these folks, i have used em several times now.
http://www.aiaindustries.com/
|
stevesandidge
|
11/14/09 03:11pm |
Tech Issues
|
|
RE: Furnace blowing fuses
its dc, not ac, with gas doin the work. if this is the 1st time you have used it, the nest thing is probable. if you have used this frunace much, it is most likely bearings in the motor was it making noise when it tried to run before?
steve
|
stevesandidge
|
11/04/09 05:33am |
Tech Issues
|
|
RE: Converter Question
have you checked your water in your batteries? that aside, it sounds like your converter is going south. you will need a meter to check the voltage, it should be 13.5 or so.
steve
|
stevesandidge
|
11/04/09 05:23am |
Tech Issues
|
|
RE: One-Piece Windshield
get some black np-1 and caulk it. np 1 is available at any roofing supply place, and forms a hard rubber seal. the other alternative would be to have the windsheild taken out and reinstalled correctly, w/o the leak.
steve
|
stevesandidge
|
11/03/09 04:51pm |
Tech Issues
|
|
RE: Sur-Flo Smart Sensor 5.7 Pump Leak
its usually the lil rubber diaphram that seperates the water from the pressure switch. easier to replace the thing, but somebody may have an old one laying around that ya could scavenge one off of. i usually save those till i have a bad pump n swap it out so i have a good used pump.
steve
|
stevesandidge
|
11/01/09 04:13pm |
Tech Issues
|
|
RE: Steering Stabilizers
i am going with blue ox's trucenter. it is adjustable, cost around 5 to 6 hundred dollars and is not hard to install either.
steve
|
stevesandidge
|
10/31/09 07:27am |
Tech Issues
|
|
RE: Update Onan NHM ?
you don't want to run it while you are checking it on ohms, or resistance, it'll blow your fuse.
steve
|
stevesandidge
|
10/26/09 07:55pm |
Tech Issues
|
|
RE: Suburban Furnace Installation?
1. locate near the center of the rv, not on one end.
2. the return air is broughtin on the right side and the top of the furnace, when looked at from the INSIDE of the rv. these MUST NOT be blocked, restricted! the bottom may sit on the floor. the left side may be close to a wall, but some space should be there, say 1/2 inch or so. good luck
steve
|
stevesandidge
|
10/25/09 08:53am |
Tech Issues
|
|
RE: Suburban Furnace Installation?
i will go out the truck n get my servic/install manuel n post more.
steve
|
stevesandidge
|
10/25/09 08:33am |
Tech Issues
|
|
RE: Remove Battery Caps While Charging
worked in an exide battery plant here back in the mid 90's, had a few explode while being charged....ya don't wanna be in the same room with em when they do.
they don't put the caps on em when they initialy charge them at the factory, for whatever that is worth....of course they dump the acid out and refill em with a different specific gravety acid for the final shipment to the stores.
steve
|
stevesandidge
|
10/25/09 08:25am |
Tech Issues
|
|
RE: Proper RV Antifreeze Disposal
I just run a hose to my neighbors lawn and flush.
now thats funny;<)
|
stevesandidge
|
10/24/09 12:23pm |
Tech Issues
|
|
RE: Furnace Wont shut off
could also be a stuck time delay relay as well.
steve
|
stevesandidge
|
10/24/09 12:18pm |
Tech Issues
|
|
RE: Leaky Water Valve - Thetford Aqua Magic Style II
Is the item that I have pointed out in the photos the water valve?
yes
Can it be changed without taking the entire toilet out
yes
steve
|
stevesandidge
|
10/24/09 12:15pm |
Tech Issues
|
|
RE: need some hope for dometic fridge
that or a new frige is the only option. sorry to give ya bad news
steve
|
stevesandidge
|
10/21/09 07:18pm |
Tech Issues
|
