| |
Subject |
Author |
Date Posted |
Forum
|
 |
RE: Mor ryde pin box
I agree with danskool. Got mine from Tweedy's also and even talked to their tech who helped get the correct one for the trailer we have. Took about 2 hours to install by myself. Would have been less if I had help. The instructions are excellent with good pictures also.
|
lightfoot
|
09/05/12 09:54am |
Fifth-Wheels
|
|
RE: Draining water
Drainage Power is Sodium Hydroxide an acid which is just what you don't want anywhere near your trailer. I really hope that wellsronald18 was being funny or had the wrong info.
|
lightfoot
|
09/05/12 09:47am |
Fifth-Wheels
|
|
RE: Trailair Equaflex
Check the rest of your shackles for grease fittings also. Some folks have put the bolts in so the fittings are on the inside of the trailer, not outside by the wheels. Makes it easier to grease them that way. If you have a couple, I suspect that there may be many more, keep looking.
|
lightfoot
|
09/05/12 09:38am |
Fifth-Wheels
|
|
RE: Voltage 3200 towing height
I think the OP might have some additional suspension on the truck. I have a 2012 F250 6.7L 4x4 LB SC and when my V3200 is attached everything is level. I don't have the actual weights at this time, they are at home somewhere, but if I can get a picture of the setup I will post it later. My hitch is a Q20K and I have 10K axles on the TV.
|
lightfoot
|
09/05/12 07:52am |
Toy Haulers
|
|
RE: Any creative ways to store you ladder?
Why take it off the side of the trailer? I keep mine on all the time and all I did was remove the bottom step, no cutting involved so that the step can be re-installed if needed.
|
lightfoot
|
09/03/12 07:55pm |
Toy Haulers
|
|
RE: peer check on new toy hauler purchase
That dealer also handles the Voltage where the front bed is fixed and the wardrobe is in the slid-out. Almost the exact layout as the Fuzion. Compare them both before jumping into anything. Take you time.
|
lightfoot
|
08/01/12 07:06pm |
Toy Haulers
|
|
RE: New Decals for our Raptor
Had to replace one on my previous TH. It was not that hard, but a slow process getting the original one off. Get a corner started and then very slowly pull the decal up and away from the wall. My hardest part was getting the new decal in the correct position. The job is not hard, just long.
|
lightfoot
|
07/12/12 11:33am |
Toy Haulers
|
|
RE: Voltage 3905 rear stabilizers and keyless entry
Can't help with the rear stabilizer as ours has not had a problem, knock on wood. The keyless entry does have a fuse, it is in the front compartment with the generator. Can't tell you where, but it is one of the plug in automotive types in a separate holder.
|
lightfoot
|
07/11/12 07:57am |
Toy Haulers
|
|
RE: Rear Spot Lights
Do you have a bank of switches that are for the outside security lights? If so try having someone walk around the outside and you start flipping switches. We had to do that due to the interesting labeling of the lights on our panel.
|
lightfoot
|
07/11/12 07:50am |
Toy Haulers
|
|
RE: Voltage 3200 fuel station question
On my 3200 the front is Fuel Station and rear is Generator. No built in cross-over. Hose from Fuel station reaches with a couple of feet to spare. The tanks are next to each other.
|
lightfoot
|
07/02/12 09:26am |
Toy Haulers
|
|
RE: HELP! Ramp too high
You must have something with almost no ground clearance that you are running up that ramp. I have a fellow motorcyclist with a custom Harley that has 4" of clearance and he gets that in his Raptor 26FS with no problems. Try raising the front of the trailer to start with or adding taller bumpers to the ramp door. If you add bumpers, and I have seen this done, you might have to add an extension to the top of the ramp that you can fold out when the ramp is down.
|
lightfoot
|
06/26/12 07:46am |
Toy Haulers
|
|
RE: Are the 2013 voltage any better than the 2011/2012's ?
We have had our 2011 3200 for 2 years now and have been out in all kinds of weather, rain, hail, snow and even sunshine, with no problems. We did have the 2nd AC installed in the front bedroom, and that made a world of difference in the speed of cooling the whole rig.
|
lightfoot
|
06/21/12 03:30pm |
Toy Haulers
|
|
RE: Schwintek slide problem!!!!!
It would be nice to know if whatever was sent and installed worked or is there still a problem. Also where is the info on the recall? One of my slides acts up every once in a while. All I have to do if it doesn't shut right the first time is run it back out about half way and back in and it shuts completely.
|
lightfoot
|
06/04/12 08:45pm |
Fifth-Wheels
|
|
RE: Suggestions for Toy Hauler
You didn't mention what tow vehicle you might be using. We would hate to give a bunch of suggestions and find that you don't have a TV that will get you where you are going. Also, if you do get to a final decision on a TH, don't believe everything that the dealer tells you about your TV. Ask us on this forum first. There have been many discussions about the weight of the Toy Haulers and the tow vehicle, so you might also do a search on that topic.
If interested, you might also try the unit listed in my sig.
|
lightfoot
|
06/03/12 02:34pm |
Toy Haulers
|
