RV.Net Open Roads Forum: Search

RV Blog

  |  

RV Sales

  |  

Campgrounds

  |  

RV Parks

  |  

RV Club

  |  

RV Buyers Guide

  |  

Roadside Assistance

  |  

Extended Service Plan

  |  

RV Travel Assistance

  |  

RV Credit Card

  |  

RV Loans

Open Roads Forum Already a member? Login here.   If not, Register Today!  |  Help

Newest  |  Active  |  Popular  |  RVing FAQ Forum Rules  |  Forum Posting Help and Support  |  Contact  



Open Roads Forum  >  Search the Forums

 > Your search for posts made by 'Missionstreet' found 44 matches.

Sort by:    Search within results:
Page of 3  
Next
  Subject Author Date Posted Forum
RE: Magic Chef Stove identify

Serial number help scroll down it gives a breakdown via serial number for serial number. Ahh yes I tried this and it would indicate my model is a series 10. However the diagrams for 10 don't match.
Missionstreet 01/23/23 10:13am Tech Issues
RE: Magic Chef Stove identify

Yes trying to replace leaky burner and defective ignition flash tubes. Series number is not present on label. Only model and serial. Long shot since they seem unavailable anymore but at least I have peace of mind thay I've got the right part numbers. Probably just have to replace the whole stove.
Missionstreet 01/22/23 12:12pm Tech Issues
Magic Chef Stove identify

I have a Magic Chef model CLY1632BDB How do I determine the "series" number? (10,11, etc.)
Missionstreet 01/21/23 02:11pm Tech Issues
RE: Slab sinking

You are lucky it's just a slab. One corner of my home foundation has sunk, as much as 1/2" depending on the season. From what I read it's going to cost $thousands to have it jacked up and stabilized. Contractors.... Haha. Actually I *think* I have that problem as well. 100+ year old brick home. Helical piers anyone?
Missionstreet 01/01/23 05:02pm General RVing Issues
RE: Slab sinking

What is coordinated pipe? Do you mean corrugated pipe; if so, and it is under the section that is sinking, it may have collapsed. Actually I meant to say perforated pipe. I have looked down from the side where it comes out on the slope and looks ok. Will try my Depstech scope for more details.
Missionstreet 01/01/23 04:58pm General RVing Issues
RE: Slab sinking

I had my driveway raised by the injection method. Very happy with the result, and it was a lot cheaper than I expected. Would you mind sharing any more details?
Missionstreet 01/01/23 05:25am General RVing Issues
RE: Slab sinking

Sure a little uneven don't bother me. As long as it's not going to move enough to cause issues. I have heard of polylevel something. I think foam injection that lifts concrete? Maybe cheaper than other alternatives?
Missionstreet 01/01/23 03:30am General RVing Issues
RE: Slab sinking

This is existing from a previous owner
Missionstreet 12/31/22 11:43pm General RVing Issues
RE: Slab sinking

Humm I wonder how much it'll sink
Missionstreet 12/31/22 11:43pm General RVing Issues
Slab sinking

This topic has been moved to another forum. You can read it here: 30375394
Missionstreet 12/31/22 04:35pm Class C Motorhomes
Slab sinking

I have a relatively new concrete slab that is about 23 by 13'. It is built on a bit of a grade with coordinated drainage pipe underneath. It really is two pieces, 12x13 each. I noticed the side closer to the slope sunk about 1/4" to *gasp* 1/2" near the center where they meet after backing up into it and then changing direction again. (There is a perpenducular crack in the center to so it isn't sinking evenly) Any thoughts?
Missionstreet 12/31/22 04:35pm General RVing Issues
Onan microlite 4000 wire routing question

I am putting my Spec E generator back together but can't remember where to route this black 110v hot wire to the breaker switch through. Does anyone know if it just goes with the other harness below the control and regulator plugs on the shield? Or does it go on the bottom through the bristles, or elsewhere? Thanks
Missionstreet 11/06/22 03:45am Class C Motorhomes
RE: Let's talk Dana 80 axle temps

I think we are off topic
Missionstreet 07/25/22 09:30am Tech Issues
RE: Let's talk Dana 80 axle temps

I have a dana 80. 1999 F53
Missionstreet 07/23/22 07:27pm Tech Issues
RE: Let's talk Dana 80 axle temps

To the best of my knowledge , this is a full floating axle that is oil bathed. With an idea of some average temps I would gain peace of mind until I am able to pull the cover + shafts and inspect the hub bearings along with diff.
Missionstreet 07/23/22 04:09pm Tech Issues
Let's talk Dana 80 axle temps

I've noticed my rear hubs are awfully hot to the touch this summer after cruising at no more than 50 mph for an hour on the highway. No dragging brakes here. I am going to get a contactless thermometer soon. Dana 80 rear, Ford says 9,450 lb on the GAWR rear, is this derated?
Missionstreet 07/21/22 11:12pm Tech Issues
RE: Magic Chef Stove Burner repair or replace?

Yes I think I'll definitely be looking for s A replacement part if I can find one! Thank you
Missionstreet 07/21/22 11:05pm Tech Issues
RE: Magic Chef Stove Burner repair or replace?

It also seems to be coming (the flame) out of those small holes where the flash tube (another rusted component I can't find) connects.
Missionstreet 06/29/22 09:02pm Tech Issues
RE: Magic Chef Stove Burner repair or replace?

Wow I didn't consider all these truths. Propane is heavy and sinks right? I guess I'm lucky it decided to ignite before it accumulated beneath the stove. How hot does that crimped area where it is rusted reach? Does the blower exhaust fan running provide any safety for a situation like this?
Missionstreet 06/29/22 06:27pm Tech Issues
RE: Magic Chef Stove Burner repair or replace?

Try contacting Colaw for either new or good used replacement. Sounds and looks like it is rusting through. I'm wondering exactly how and where it is rusting, if the propane is escaping out the bottom and igniting is there some way to seal it?
Missionstreet 06/29/22 09:46am Tech Issues
Sort by:    Search within results:
Page of 3  
Next


New posts No new posts
Closed, new posts Closed, no new posts
Moved, new posts Moved, no new posts

Adjust text size:




© 2023 CWI, Inc. © 2023 Good Sam Enterprises, LLC. All Rights Reserved.