 |

|
|
Highway 4x4

La Verne, Ca

Senior Member

Joined: 12/07/2006

View Profile

Offline
|
Here in So Cal, Irwindale, they quoted me 575 for a claen and re pack of 2 axle 5200 pound. I do my own. one at a time.
|
deadticket8

All over

Senior Member

Joined: 02/10/2006

View Profile


Good Sam RV Club Member
Offline
|
hey you know what? I just wanted a few thoughts not a full out Donnybrook! I appreciate the people with hands on knowledge and their input. Interesting post about containers. I think I will invest in a floor jack and do it myself. Last time I went cross country and back and the down south without issues so I musta dun good!Would be nice to know bearing sizes before hand just in case I need replacement.
|
deadticket8

All over

Senior Member

Joined: 02/10/2006

View Profile


Good Sam RV Club Member
Offline
|
Found someone that will do it for $200 plus seals. He maintains a fleet of vehicles (ambulances, medical pickup business) and does cashies. He just did bearings on 3 snow mobile trailers so he knows the drill.
|
ken56

Tennessee

Senior Member

Joined: 01/12/2013

View Profile


Good Sam RV Club Member
Offline
|
Just paid 100 bucks a wheel to have mine done. To me it's worth it even though I COULD do it myself I DON'T WANT TO DO IT MYSELF. They checked the brake pads and current going to the magnets and made sure they were operating properly. Well worth the money I paid I feel.
|
MFL

Midwest

Senior Member

Joined: 11/28/2012

View Profile


Good Sam RV Club Member
Offline
|
It seems the OP found someone to do his bearing service at a good price.
To ken56 above, that is a bit overpriced, IMO! However, if you don't want to do it, and the person doing it has a great reputation for quality work, it is worth it to you.
I use going to the dentist, as a comparison, for paying too much for a service done. Just a filling can be $500, and a crown easily 1K+, for just an hours work! So, who isn't happy, after getting a tooth repaired?? I have never said "I wished I wouldn't have gotten that tooth fixed".
Hope no dentists on these forums, but just giving my tip for justification, for maybe spending too much! ![smile [emoticon]](http://www.rv.net/sharedcontent/cfb/images/smile.gif)
Jerry
|
|
Grit dog

Black Diamond, WA

Senior Member

Joined: 05/06/2013

View Profile

Offline
|
ken56 wrote: Just paid 100 bucks a wheel to have mine done. To me it's worth it even though I COULD do it myself I DON'T WANT TO DO IT MYSELF. They checked the brake pads and current going to the magnets and made sure they were operating properly. Well worth the money I paid I feel.
Good for you. And thank you for this insightful post in a dead thread.
But why are you yelling? Lol
2016 Ram 2500, MotorOps.ca EFIlive tuned, 5” turbo back, 6" lift on 37s
2017 Heartland Torque T29 - Sold.
Couple of Arctic Fox TCs - Sold
|
JRscooby

Indepmo

Senior Member

Joined: 06/10/2019

View Profile

Offline
|
MFL wrote: It seems the OP found someone to do his bearing service at a good price.
To ken56 above, that is a bit overpriced, IMO! However, if you don't want to do it, and the person doing it has a great reputation for quality work, it is worth it to you.
I use going to the dentist, as a comparison, for paying too much for a service done. Just a filling can be $500, and a crown easily 1K+, for just an hours work! So, who isn't happy, after getting a tooth repaired?? I have never said "I wished I wouldn't have gotten that tooth fixed".
Hope no dentists on these forums, but just giving my tip for justification, for maybe spending too much! ![smile [emoticon]](http://www.rv.net/sharedcontent/cfb/images/smile.gif)
Years back guy I knew from the bar was witching about how much it was going to cost to put timing chain in his small block Chevy. We agreed on price, I gathered up tools I would need, got on bicycle went to where he left car. Popped distributer cap of to rotate engine to TDC while timing mark was still visible. Saw the condenser mounting screw was missing. Dropped a dime "You want a new timing chain? Or do you want it to run?" Had it running within 30 minutes of getting to car, including trip to auto parts store. Put bike and tools in car for trip to where he was, charge 1/2 what we agreed to. He "What was wrong, for the quick fix?" Me "Who told you timing chain? The condenser was not grounded." He, "Acted just like last car that needed chain. YOU GOING TO CHARGE THAT MUCH JUST TO PUT SCREW IN?" Your not paying for what I did, your paying for what I know"
|
3ares

COLLEYVILLE,TX.

Full Member

Joined: 04/22/2004

View Profile


|
Quality in the RV industry is almost non-extant. From new units to repairs. We have a new RV made by Forest River. incomplete construction list is endless. The industry needs an independent agency that has teeth.
Happy Camping
2016 F250 Super Duty 4x2 Crew Cab XLT
6.7 Power Stroke
6 Speed Transmission
3.31 Electronic Locking Axle
Pullrite 16K Super Glide Hitch
2012 Sundance 275 RE XLT Fithwheel
|
Vintage465

Prunedale CA.

Senior Member

Joined: 05/02/2015

View Profile

Offline
|
Well, this has been fun......I've packed my bearings all my RV life and during the time I worked at my dad's RV shop. I think it takes about 45 minutes to an hour a hub to:
1. Jack it up and place safety stands
2. Remove wheel, hub, bearings and clean.
3. Grease and reassemble w/new seals
4. Adjust play and remove jack and stands.
I'd say it's a 1/2 day job. I've alwasy had a place to do this type work, so I can. Not everyone has this option so, to find someone you trust to do a good job that charges a c-note per wheel doesn't really seem that out of line.
V-465
2013 GMC 2500HD Duramax Denali. 2015 CreekSide 20fq w/450 watts solar and 465 amp/hour of batteries. Retired and living the dream!
|
|
|
|
|